Book Printing & Binding

How to Prepare a Print-Ready PDF for Book Printing: Margins, Bleed, Fonts and Spine Width

Quick summary: A print-ready PDF for book printing has its page size set to the final trim size, margins with a wider gutter for perfect binding, 3 mm bleed wherever anything touches the edge, embedded fonts, 300 dpi images and single pages exported as PDF/X-1a or high-quality print. The cover is a separate single-page file laid out as back + spine + front, with spine width worked out from page count and paper caliper, and confirmed by the printer before you finalise.

Key facts

  • Set the document page size to the final trim size (A5 is 148 x 210 mm), never A4 for an A5 book
  • Use 3 mm bleed on all sides whenever colour, images or backgrounds touch the page edge
  • Keep text and page numbers at least 12 to 15 mm from the trim and give the gutter extra room for perfect binding
  • Embed all fonts, use 300 dpi images at final size, and export single pages, not spreads
  • Set body text to 100% K black, not rich black or RGB black
  • The cover is a separate one-page file: back cover + spine + front cover, with bleed all round
  • Spine width = (pages divided by 2) x paper caliper per leaf, plus cover thickness; we confirm the exact figure before you finalise

Young authors come to our counter in Kapoorthala all the time with a novel of about 240 pages on a pen drive, relieved that the manuscript is finally done. Typically the file is an A4 Word document, the book is meant to be A5, and the cover is a single JPEG with the title sitting barely 2 mm from the edge. We sort it out together over a couple of visits, but it costs the author a week they did not need to lose. This guide is everything we would tell them before they press Export.

Quick answer

A print-ready PDF for book printing is a file where the page size equals the final trim size, the margins and gutter are set for the binding you have chosen, 3 mm bleed is added wherever colour or images touch the edge, every font is embedded, images are 300 dpi at the size they will print, and the file is exported as single pages (not spreads) using a PDF/X-1a or high-quality print preset. The cover is a separate one-page file laid out as back cover + spine + front cover, with the spine width worked out from your page count and the paper caliper. Get these right and the digital proof we send back from Lucknow will look exactly like the book you imagined, whether it is couriered to Delhi, Mumbai or Bengaluru.

Why the print-ready PDF for book printing matters more than the design

Most books that get delayed at our shop are not delayed because of printing. They are delayed because the file needs to be fixed, sent back, re-exported, and checked again. A beautifully designed book with the wrong page size takes longer to produce than a plainly designed book with a clean file. Every press, digital or offset, works the same way: it prints exactly what the PDF says, then trims the paper to the size you asked for. If the PDF and the trim size disagree, something has to give, and it is usually your margins.

So before thinking about fonts and colours, think like a binder. Where will the knife cut? Where will the glue sit? How much of the inner margin disappears into the spine? Once you picture the physical object, every rule below becomes obvious rather than arbitrary. If you want a refresher on what the different binding styles actually look like in hand, our paperback vs hardcover vs spiral binding guide walks through them with photos of real jobs.

Step 1: Set the page size to the final trim size

This is the single most common mistake we see, and it is also the easiest to avoid. If your book will be A5, your document must be A5 (148 x 210 mm). Not A4 scaled down. Not Letter. Not “we will shrink it at the press.” Shrinking an A4 layout to A5 reduces your 11-point body text to roughly 7.8 points, which is unreadable for most adults, and your margins shrink with it.

The trim sizes we print most often are:

  • A5 (148 x 210 mm): novels, poetry, devotional books, most self-published titles.
  • 5.5 x 8.5 inches (140 x 216 mm): a popular trade paperback size for fiction and memoir.
  • 6 x 9 inches (152 x 229 mm): non-fiction, business books, textbooks with wider margins.
  • A4 (210 x 297 mm): coaching study material, workbooks, theses, magazines and yearbooks.
  • Custom sizes: square children’s books, pocket editions, landscape photo books. Ask us before you lay out a custom size so we can confirm paper yield and binding.

In Word, LibreOffice and Google Docs, this is under Page Setup or Page Size, and you type the dimensions in millimetres. In InDesign, Scribus and Affinity Publisher, you set it when you create the document, with a separate field for bleed. In Canva, pick a custom size in millimetres and remember that Canva adds bleed only when you tick the option at export. Set the size on day one, before you type a word, because changing it later reflows every page and shifts every chapter start.

Step 2: Margins, gutter and the safe zone

Margins do two jobs. They keep text away from the trim so nothing is cut off, and they give the reader’s thumbs somewhere to rest. For a perfect bound (paperback) book, the inside margin needs to be wider than the outside, because a few millimetres of every page disappear into the glued spine and the book does not open completely flat.

Margins we recommend for common bindings

BindingInside (gutter)OutsideTopBottom
Perfect binding, up to 200 pages18 to 20 mm13 to 15 mm15 mm18 mm
Perfect binding, 200 to 500 pages20 to 22 mm13 to 15 mm15 mm18 mm
Hardcover (case bound)20 to 22 mm15 mm15 mm18 mm
Saddle stitch (up to about 48 pages)13 mm13 mm13 mm15 mm
Spiral or wiro20 mm (for the punch holes)13 mm13 mm15 mm

These are starting points, not laws. Textbooks with marginal notes want more outside margin; poetry can afford less. The number that matters most is the gutter. If you are preparing a thick coaching module or a thesis that will be perfect bound, 20 mm on the inside is the minimum we would print without a warning on the proof.

Mirror margins

Word, LibreOffice and Google Docs all have a “mirror margins” or “facing pages” option. Switch it on. Without it, your wide gutter margin will sit on the left of every page, which means it is correct on right-hand (odd) pages and wrong on left-hand (even) pages. InDesign and Scribus handle this automatically when you create the document with facing pages.

The safe zone

Trimming is a mechanical process and every press has a small tolerance, usually a millimetre or so either way. The safe zone is the area at least 5 mm inside the trim where important content must stay. In practice, your margins already keep body text well inside it. The things that get caught are page numbers set too low, running headers set too high, and decorative borders that look fine on screen but end up cut unevenly on paper. Keep page numbers at least 12 mm from the trim and no border closer than 6 mm.

Step 3: Bleed, and when you actually need it

Bleed is extra image or colour that extends 3 mm beyond the trim on every side. The press prints the page slightly oversize and the trimmer cuts it down, so if a background colour or photo stops exactly at the trim line, any tiny shift during cutting leaves a thin white sliver along the edge. Extending the artwork 3 mm past the edge means the knife always lands on colour.

You need bleed when:

  • A full-page photograph, illustration or colour panel touches the edge.
  • Chapter opener pages have a coloured background or a tinted band.
  • Side tabs, index markers or thumb-tabs are printed at the page edge (common in study material).
  • The cover, always. Every cover file needs bleed on all four sides.

You do not need bleed for a plain text book with white margins. A novel set in black text on white paper can be exported at exactly 148 x 210 mm and we will be happy. Adding bleed to a book that does not need it does no harm, but adding it wrongly does: we regularly receive A5 PDFs at 154 x 216 mm where the author simply made the page bigger without extending any artwork, which puts white borders inside the trim and throws the margins off.

Practical tip: If your layout program supports a bleed setting, use it and export with “include bleed” ticked. If you are in Word or Google Docs, which do not have a bleed setting, keep your interior design away from the edges entirely and leave bleed to the cover, which you design separately. Trying to fake bleed in Word by enlarging the page almost always goes wrong.

Step 4: Single pages, blank pages and the right page count

Export your interior as single pages, one page per PDF page, in reading order. Not two-page spreads, not booklet-imposed, not “2 up.” Imposition is our job; the press software arranges pages onto sheets based on the binding. A PDF supplied as spreads has to be split apart first, and if a spread has a photo crossing the middle, the split is never clean.

Blank pages are part of the book

In a printed book, chapters traditionally begin on a right-hand (odd-numbered) page. If chapter 3 ends on page 57, page 58 should be blank and chapter 4 begins on 59. That blank page must be in your PDF as an actual blank page. If you leave it out, every chapter after that point flips to the wrong side, and your mirrored margins swap too. The same applies to the front matter: the title page sits on the right, the copyright page on its reverse, the dedication on the right, and so on. Count your pages after inserting the blanks, not before.

Why the total must be divisible by 2, and ideally by 4

A leaf of paper has two sides, so a book always has an even number of pages. If your PDF has 237 pages, the last page will be blank whether you include it or not, so include it and decide what goes there. For saddle stitched booklets, folded sheets give four pages each, so the total must be a multiple of 4: 16, 20, 24, 28 and so on. A 30-page saddle stitched booklet becomes a 32-page booklet with two blanks at the back, and it is better that you decide where those blanks go than that we do. For perfect binding and spiral, divisible by 2 is enough, though many presses print in signatures of 4 or 8, so a multiple of 4 avoids stray blanks at the end.

Step 5: Fonts, embedding and the flatten question

A PDF carries the shapes of your letters only if the fonts are embedded. If they are not, the computer opening the file substitutes something else, and your carefully set Garamond becomes a default sans-serif with different widths, so lines break differently and pages overflow. Modern export dialogs embed fonts by default, but not always, and a few things break it:

  1. Fonts with licence restrictions that forbid embedding. Some free fonts downloaded from random sites have this flag set. Use fonts from reputable sources or system fonts.
  2. “Print to PDF” through a generic printer driver instead of using the program’s own Export or Save as PDF. The driver sometimes rasterises or substitutes.
  3. Hindi, Urdu, Sanskrit and other Indic scripts set in older non-Unicode fonts (the ones where you type English letters and they show as Devanagari). These often fail to embed. Unicode fonts like Noto Sans Devanagari or Mangal embed cleanly.

To check, open your PDF in any reader, go to File, Properties, Fonts, and confirm every font listed says “Embedded” or “Embedded Subset.” If one does not, fix it before sending.

Should I flatten or outline the text?

Customers sometimes ask, “Sir, text ko outline kar dein?” For the interior, no. Converting text to outlines makes the file enormous, makes thin text look slightly heavier, and removes the ability to search or correct a typo. Embedding is enough. For the cover, outlining the title text is acceptable and sometimes sensible if you used a decorative font you are not certain will embed, but keep an editable version for yourself. “Flattening” in the sense of merging transparency layers is handled automatically by the PDF/X-1a preset and you do not need to do it by hand.

Step 6: Images and colour

Images at 300 dpi at final size

Resolution is about how many pixels an image has for the size it will print. The standard for sharp printing is 300 dots per inch at the printed size. An A5 full-page photo (148 x 210 mm, which is 5.8 x 8.3 inches) therefore needs about 1750 x 2480 pixels. A half-page diagram needs half that. A photo pulled from WhatsApp or a website is usually 800 to 1200 pixels wide and prints acceptably at about 7 to 10 cm, no more.

Things that help:

  • Insert images at the size they will print rather than placing a huge image and shrinking it, which bloats the file, or placing a tiny one and stretching it, which blurs.
  • Use Word’s or Google Docs’ setting to not compress images on export. Both compress to screen resolution by default unless you change the option.
  • Scanned line drawings, formulas and handwritten solutions (common in coaching material) look best scanned at 600 dpi as black and white, not as colour photos of the page.
  • Logos and diagrams should be vector (SVG, EPS, PDF) wherever possible. They stay sharp at any size and add almost nothing to file size.

The cover deserves special attention. A low-resolution cover is the error that disappoints authors most, because the cover is what everyone sees first. A cover designed in Canva at the default web size, then downloaded as a small JPEG, will print soft and pixelated. Design the cover at the full flat size with bleed, and download as PDF Print or at 300 dpi.

Colour, black text and what digital printing actually does

Three colour questions come up on almost every job.

Black text should be 100% K

Body text should be pure black, which in CMYK terms is C0 M0 Y0 K100. “Rich black,” a mix like C60 M40 Y40 K100, is for large solid areas on covers where it gives a deeper tone. If body text is set in rich black or in RGB black (which converts to a four-colour mix), every letter is printed with four passes of toner, and any microscopic misregistration shows as a coloured fringe around the letters. Word and Google Docs use RGB black by default, and on a digital press this normally converts to a near-pure black without trouble, but if you have the option in your layout software, set text to K100 explicitly.

RGB versus CMYK

Screens show colour as RGB light; presses print with CMYK toner or ink. CMYK cannot reproduce some bright RGB colours, particularly vivid blues, saturated greens and neon oranges. Those shift to a slightly duller version on paper. Professional layout software lets you work in CMYK from the start so you see roughly what you will get. Word, Docs and Canva work in RGB and the press converts on the fly, which is fine for most books. The practical advice is simple: do not expect the printed cover to glow like your laptop screen, and if a colour is critical, say a brand blue for a corporate training manual, ask us for a physical sample before the full run. We offer a sample copy on every bulk order for exactly this reason, and we go into it in detail in our bulk book printing guide for publishers and institutions.

Colour consistency inside the book

If your interior is colour (printed on 100 to 130 gsm art paper), keep the same image profile throughout. A mix of CMYK and RGB images on facing pages can print with a visible difference in the same red. Convert everything to one colour mode before you lay out.

Step 7: Exporting the PDF

This is the step that turns your layout into a print-ready PDF for book printing, so it is worth doing carefully. Every program has an export route. Use the one built in to the application, not a generic virtual printer.

  • Word: File, Save As, PDF, then Options, and tick “PDF/A” or “ISO 19005-1 compliant” if you want fonts forced to embed. Choose “Standard (publishing online and printing),” not “Minimum size.”
  • Google Docs: File, Download, PDF Document. Docs gives you no quality options, so make sure your images were inserted at full resolution. For a book with many images, consider finishing the layout in LibreOffice or a dedicated tool.
  • LibreOffice: File, Export As, Export as PDF, and in the dialog set JPEG quality to 100 or lossless, untick “reduce image resolution,” and tick PDF/A if you want strict embedding.
  • InDesign, Affinity Publisher, Scribus: Export with the PDF/X-1a:2001 preset, include document bleed settings, no printer’s marks, and spreads unticked for the interior.
  • Canva: Share, Download, PDF Print, tick “crop marks and bleed” only for the cover, and choose CMYK if your plan offers it.

PDF/X-1a is a print-exchange standard that flattens transparency, embeds all fonts and converts colour to CMYK, which is why most presses ask for it. If your software does not offer it, “High Quality Print” or “Press Quality” is fine. After export, open the file and check three things: page count, page size (in Properties), and that fonts are embedded. Then scroll through every page once. It takes ten minutes and catches things software does not.

One more point about marks. Crop marks, registration marks and colour bars belong outside the page, in the bleed and slug area, and only on files exported with bleed. We sometimes receive interior PDFs where the crop marks have been drawn inside the page as part of the design, or the author exported with marks on a page that has no bleed, so the marks sit inside the trim and print on the finished book. Export your interior with no marks at all. Our workflow does not need them.

Step 8: The cover file, laid out flat with the spine

The cover is a separate file, one page, landscape, showing the whole wrap as it will be printed before folding: back cover on the left, spine in the middle, front cover on the right, with 3 mm bleed on all four outer sides. The press prints this flat on 250 to 300 gsm art card, laminates it, and the binding machine wraps it around the book block.

Calculating the spine width

Spine width depends on two things: how many leaves of paper are in the book, and how thick each leaf is. The thickness of a sheet is called its caliper, measured in millimetres or microns, and it varies by paper type and mill even at the same gsm. The method is:

  1. Divide your page count by 2 to get the number of leaves. A 240-page book has 120 leaves.
  2. Multiply the leaves by the caliper of one sheet. For the 70 to 80 gsm uncoated book papers most commonly used for black and white interiors, the caliper is usually somewhere around 0.09 to 0.11 mm per sheet. For 100 to 130 gsm coated art paper used in colour books, it is typically a little lower per gsm because coated paper is denser, often around 0.08 to 0.12 mm depending on the stock.
  3. Add the thickness of the two cover boards (roughly 0.3 mm each for 300 gsm art card) and a small allowance for the glue line.

Worked example: a 240-page A5 novel on 75 gsm paper. 240 divided by 2 is 120 leaves. At 0.10 mm per leaf, that is 12.0 mm of paper. Add roughly 0.6 mm for the two covers and around 0.5 mm for glue, and the spine is close to 13 mm. At the lower end of the caliper range (0.09 mm) it would be nearer 11.9 mm, and at the top end (0.11 mm) nearer 14.3 mm. That spread of about 2 mm is exactly why we measure the actual paper we will use and confirm the figure to you before you finalise the cover. Design your spine to our confirmed number, and keep spine text at least 2 mm clear of each spine edge so a small shift does not push a letter onto the front or back.

The full flat cover size for that A5 example would be: width = 3 mm bleed + 148 mm back + 13 mm spine + 148 mm front + 3 mm bleed = 315 mm; height = 3 + 210 + 3 = 216 mm. Set your cover document to 315 x 216 mm (or 309 x 210 mm with a 3 mm bleed setting, which comes to the same thing), and draw a guide at 151 mm and 164 mm from the left for the spine edges.

Spine text direction

Most English-language books in India follow the convention where spine text reads from top to bottom, so that when the book lies on a table with the front cover facing up, the spine title reads correctly left to right. Some Hindi and regional-language publishers follow the opposite direction. Neither is wrong, but pick one and keep it consistent across a series. Books under about 80 pages have spines too thin for text; leave them blank rather than cramming in 6-point lettering.

Barcode and ISBN placement

If your book has an ISBN (issued free in India by the Raja Rammohun Roy National Agency through the isbn.gov.in portal), the barcode goes on the back cover, usually in the lower right or lower centre, on a white or very light rectangle, at least 10 mm from any trim edge, and printed in pure black. Do not place it over a photograph or a dark colour, do not shrink it below about 80% of the standard size, and do not stretch it. We print the barcode exactly as you supply it; generating and verifying it is part of your ISBN process, and our self-publishing guide explains that process end to end.

Lamination and dark covers

Our covers get gloss or matt lamination. Matt lamination looks elegant and photographs well, but on very dark or black covers it shows scuffs and fingerprints more readily than gloss, especially after a courier journey to Kolkata or Chennai. If your cover is predominantly black or deep navy and the book will be handled a lot, gloss is the safer choice, or consider a design that is not solid dark edge to edge. Also remember that lamination slightly deepens colours and matt lamination slightly softens contrast, which is another reason to see a printed sample on a bulk run. Our paper, GSM and lamination guide goes deeper into those choices.

Step 9: Naming, sending and proofing your files

Naming your files

Name files so that anyone can tell what they are without opening them, and so that versions do not get mixed up. A pattern that works:

  • BookTitle_Interior_A5_240pp_v3.pdf
  • BookTitle_Cover_315x216_spine13_v2.pdf

Include the page count in the interior filename and the spine width in the cover filename. When one changes, the other usually must too, and the names make that obvious. Send both files together even if only one changed, and tell us clearly which version supersedes which. “Final,” “Final2” and “FinalFINAL” are not version numbers.

Getting big files to us

WhatsApp compresses images but sends PDFs as documents without altering them, up to its file size limit (which has been around 2 GB on current versions, though this changes). Send as a document, not as a photo. For anything larger, or for multiple files, upload to Google Drive, Dropbox or a similar service and share a link with view access turned on for anyone with the link. A WeTransfer-style link also works. Do not paste the interior into an email in pieces. If you are sending from a phone, double-check that the PDF you shared is the exported one and not a screenshot of it, which happens more often than you would think.

What our proof checks catch, and what they do not

When your print-ready PDF for book printing reaches us, we run it through a pre-flight check and send you a digital proof before anything is printed. On bulk runs we also make one physical sample copy. Our checks look for:

  • Page size mismatch between the file and the ordered trim size.
  • Mixed page sizes within one PDF (a stray A4 page in an A5 book, usually an appendix or a chart).
  • Fonts not embedded.
  • Images that will print below about 150 dpi, which we flag as a warning, and below 100 dpi, which we flag as a stop.
  • Content inside the 5 mm safe zone, especially page numbers and headers.
  • Odd page counts, and chapter starts falling on left-hand pages.
  • Cover flat size that does not match the spine width we calculated for the page count and paper.
  • Crop marks or colour bars sitting inside the trim.
  • Bleed missing on a cover or on full-bleed interior pages.

What we do not catch, because no printer can, is a typo, a wrong chapter order, a missing figure caption or an outdated phone number on the back cover. The proof is your chance to read the book as a book. Please read it. Once you approve the proof and we start printing, a change means reprinting those pages, and on a run of 500 copies that is real paper and real time.

Print-ready PDF for book printing: pre-flight checklist and common errors

Pre-flight checklist

CheckInterior PDFCover PDF
Page size equals trim size (plus bleed if used)Yes, e.g. 148 x 210 mm for A5Yes, full flat size: back + spine + front + 6 mm bleed
Bleed 3 mm on all sidesOnly if artwork touches the edgeAlways
Margins and gutterInside 18 to 22 mm for perfect binding, mirroredNot applicable, but keep text 5 mm inside trim and 2 mm off spine edges
Single pages, reading orderYes, no spreads, no impositionOne landscape page
Page countEven; multiple of 4 for saddle stitch; blanks includedMatches spine calculation
FontsAll embeddedAll embedded or outlined
Images300 dpi at final size; 600 dpi for scanned line art300 dpi at full flat size
Black textK100 where the software allowsBarcode in K100 on white
Colour modeConsistent; CMYK preferred, RGB acceptableCMYK preferred
Export presetPDF/X-1a or High Quality Print, no marksPDF/X-1a with bleed, marks optional
File nameTitle_Interior_Size_Pages_vN.pdfTitle_Cover_FlatSize_SpineN_vN.pdf

Common errors and how to fix them

Error we seeWhat goes wrong in printFix
Text or page numbers within 5 mm of the trimCut off or sitting uncomfortably at the edge after trimmingMove content inside the safe zone; increase bottom margin for page numbers
Low-resolution cover (web JPEG, screenshot)Soft, pixelated title and image, visible on every copyRebuild the cover at full flat size and export at 300 dpi as PDF Print
Fonts not embeddedSubstitute font, changed line breaks, pages overflow, symbols become boxesExport with the program’s own PDF exporter; check Properties, Fonts; switch non-embeddable fonts
Mixed page sizes in one PDFStray pages scale or get trimmed differently; margins jumpSet every section to the same page size before combining; check Properties on the merged file
Crop marks inside the pageLittle black lines printed on the finished bookExport interior with no marks; for covers, marks only in the bleed area
A4 layout for an A5 bookText shrinks to around 70% and becomes unreadableReflow the document at the real trim size
Spreads exported instead of single pagesPages must be split; images crossing the middle breakUntick Spreads on export
Odd page count, missing blanksChapters start on left-hand pages; margins swap sidesInsert blank pages where needed; finish on an even count
Spine width guessed, not confirmedSpine text wraps onto front or back coverAsk us for the figure for your exact page count and paper before finalising
Rich black or RGB black body textColoured fringes around letters, heavier lookSet body text to C0 M0 Y0 K100

Special cases: theses, coaching material and spiral books

Everything above about a print-ready PDF for book printing applies to a standard novel or non-fiction paperback. A few jobs have their own quirks.

Theses and dissertations

Universities set the trim size (almost always A4), the margins (often a 1.5 inch left margin for binding) and sometimes the font and spacing. Follow the university first, then our advice. Most theses are hard bound with spine lettering, so you also need to tell us the exact text for the spine and the front board. Our thesis printing and binding page lists what to send, and the thesis binding requirements guide covers common university norms.

Coaching institute study material

Study material is usually A4, black and white on 70 to 80 gsm, with many scanned pages of solved problems and diagrams. The traps are scanned pages at odd sizes, pages photographed rather than scanned, and modules assembled from many PDFs with different margins. Standardise every module to A4, scan at 600 dpi black and white, and give the gutter 20 mm because these books are opened and closed hundreds of times. See study material printing for coaching institutes for the specs we recommend.

Spiral and wiro bound books

Spiral opens 360 degrees and lies flat, which is why coaching institutes and training teams love it, but the punch holes eat about 8 to 10 mm along the binding edge. Set the gutter margin to at least 20 mm and keep nothing important within 15 mm of that edge. Spiral books have no printed spine, so the cover is two separate pages (front and back) rather than a wrap. Details are on our spiral and wiro binding page.

How we handle this at Malka Xerox Centre

At our shop in Yadav Market, Kapoorthala, Lucknow, every book order goes through the same sequence, whether it is one thesis for a student from Aliganj or 800 copies of a training manual going to Hyderabad and Pune. You send the interior and cover files on WhatsApp or by Drive link. We pre-flight them against the trim size, binding and paper you have chosen and reply with the exact spine width for your page count and paper. If something needs fixing, we tell you what and why, in plain words, and if you are stuck we can make small corrections like adding blanks or adjusting a cover size for you. Then we send a digital proof, and on bulk orders a physical sample copy. Only after your approval do we print.

Most runs are ready in 2 to 5 working days from approval, and tracked courier takes roughly another 2 to 5 working days depending on the city, so a book headed to Jaipur or Kota usually arrives within a fortnight of the file being locked. Every order carries a GST invoice. We print inside pages black and white on 70 to 80 gsm or colour on 100 to 130 gsm art paper, covers on 250 to 300 gsm art card with gloss or matt lamination, and we bind by perfect binding for roughly 60 to 500 pages, hardcover with cloth or printed wrap, saddle stitch up to about 48 pages, and spiral or wiro. If you already have a finished PDF and just want it printed, our print a book from PDF page is the quickest starting point, and the full range is on our book printing page. Pricing depends on page count, paper, colour and quantity, and we have written up what moves the number in our book printing cost guide.

Key takeaways

  • Set the document to the final trim size before you write a word. A5 is 148 x 210 mm; never submit A4 for an A5 book.
  • Use mirrored margins with a gutter of 18 to 22 mm for perfect binding, and keep page numbers at least 12 mm from the trim.
  • Add 3 mm bleed only where artwork touches the edge in the interior, and always on the cover.
  • Export single pages in reading order, with blank pages included, to an even total (multiple of 4 for saddle stitch).
  • Embed every font and check it in the PDF’s properties. Use 300 dpi images at printed size, 600 dpi for scanned line art.
  • Set body text to K100 black and expect CMYK printing to be a little less vivid than your screen.
  • The cover is a separate flat file: back + spine + front + bleed. Spine width is leaves times caliper plus cover thickness; ask us to confirm the figure before you finalise.
  • Name files with page count and spine width, send as documents on WhatsApp or via Drive link, and read the proof as a reader, not just as a designer.
  • A print-ready PDF for book printing is not about expensive software. Word or Docs can produce one if the page size, margins, fonts and page count are right.

If you are halfway through a layout and unsure whether your print-ready PDF for book printing will actually print cleanly, send us the PDF before you finish the cover. We will check the page size, margins and page count and tell you the spine width you need, free of obligation. Message us on WhatsApp +91 97927 57892, or use the contact page. We are open 7 days, 9 AM to 10 PM, and we print and courier books from Lucknow to 178+ cities across India, from Delhi and Mumbai to Patna, Varanasi and Bengaluru.

Frequently asked questions

What size should my PDF be for an A5 book?

Set the document page size to exactly 148 x 210 mm, which is A5. Do not lay out on A4 and scale down, because the text shrinks to about 70 percent and becomes hard to read. If any artwork touches the page edge, export with 3 mm bleed so the file measures 154 x 216 mm with the bleed included.

How much bleed do I need for book printing?

The standard is 3 mm on all four sides. Bleed is only needed where colour, photos or backgrounds run to the edge of the page, and it is always needed on the cover. A plain text interior with white margins does not need bleed at all.

How do I calculate the spine width of a paperback book?

Divide the page count by 2 to get the number of leaves, multiply by the caliper of one sheet of your paper, then add the thickness of the two covers and a small glue allowance. For 70 to 80 gsm book paper the caliper is usually around 0.09 to 0.11 mm per sheet, so a 240-page book comes to roughly 12 to 14 mm. We measure the actual paper and confirm the exact figure before you finalise the cover.

Should the cover be in the same PDF as the inside pages?

No. Send the cover as a separate single-page landscape PDF laid out flat as back cover, spine and front cover, with 3 mm bleed on all sides. The interior is a separate PDF of single pages in reading order. Keeping them apart lets us print the cover on 250 to 300 gsm art card and the interior on book paper.

Why does my page count need to be even?

Every sheet of paper has two sides, so a printed book always has an even number of pages. If your PDF has an odd count, the last page will be blank anyway, so it is better to include it and decide what goes there. For saddle stitched booklets the count must be a multiple of 4 because each folded sheet makes four pages.

How do I check if fonts are embedded in my PDF?

Open the PDF in any reader, go to File, Properties and then the Fonts tab. Every font listed should say Embedded or Embedded Subset. If one does not, re-export using the program's own Save as PDF or Export function rather than a generic print driver, and replace any font whose licence blocks embedding.

What resolution do images need for book printing?

Images should be 300 dpi at the size they will actually print. A full A5 page photo needs about 1750 x 2480 pixels. Scanned line drawings, formulas and handwriting look best at 600 dpi in black and white. Covers downloaded from web design tools at screen size will print soft, so export the cover at 300 dpi or as PDF Print.

Will my printed colours match my screen?

Not exactly. Screens show RGB light while presses print CMYK toner, and some bright blues, greens and oranges come out a little duller on paper. Lamination also slightly deepens colours. For covers where colour matters, ask for a physical sample copy before the full run.

Can I send my book files on WhatsApp?

Yes, send the PDFs as documents, not as photos, so they are not compressed. For very large files or several files together, upload to Google Drive or a similar service and share a link with access for anyone who has it. Name the files with the page count and spine width so versions do not get mixed up.

Do you fix files that are not print-ready?

We pre-flight every file and tell you exactly what needs changing and why. Small fixes such as adding blank pages, adjusting a cover size to the correct spine width or splitting spreads we can often do for you. Larger reflows, such as converting an A4 layout to A5, need to be done in your original document and re-exported.

Need this done at Malka Xerox Centre?

Walk in at Shop No.-10, Yadav Market, Near FI Plaza, Chandganj Kapoorthala, Lucknow, Uttar Pradesh 226022, or message us on WhatsApp to check availability.

Message us on WhatsApp

Sami Jaiswal

Written by the team at Malka Xerox Centre, Kapoorthala, Lucknow.

Chat on WhatsApp
Call WhatsApp Book